- 您现在的位置：买卖IC网 > Sheet目录1228 > MAX5977AEVKIT# (Maxim Integrated Products)EVAL KIT MAX5977A
1V to 16V, Single-Channel, Hot-Swap Controllers
with Precision Current-Sensing Output
Pin Configuration
TOP VIEW
FAULT 16
CAL 17
15
14
13
12
11
10
9
CALSENSE
SENSE
I.C. 18
I.C. 19
BIAS 20
MAX5977A
MAX5977B
EP*
8
7
6
IN
SCOMP
FCOMP
1
2
3
4
5
THIN QFN
*CONNECT TO AGND.
Pin Description
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18, 19
20
—
NAME
REG
PWR
AGND
UV
OV
FCOMP
SCOMP
IN
SENSE
CALSENSE
PG
CSOUT
GND
GATE
SOURCE
FAULT
CAL
I.C.
BIAS
EP
FUNCTION
Regulator Output. Bypass REG with a 1 F F capacitor.
Power-Supply Input. Bypass PWR with a 0.1 F F or higher value capacitor.
Analog Ground
Active-High Precision Turn-On Input. UV is used to turn on/off the output and set the input
undervoltage lockout threshold.
Active-Low Precision Turn-On Input. OV is used to turn on/off the output and set the input overvoltage
lockout threshold.
Fast Circuit-Breaker Comparator Input. Connect FCOMP to IN with a resistor to set the fast-trip circuit-
breaker threshold.
Slow Circuit-Breaker Comparator Input. Connect SCOMP to IN with a resistor to set the slow-trip
circuit-breaker threshold.
Hot-Swap Voltage-Monitoring Input
Current-Sense Voltage Input. The voltage across an external sense resistor between IN and SENSE is
used to measure the channel current.
Calibration Voltage Input
Power-Good, Active-High Open-Drain Output
Transconductance Current-Sense Amplifier Output. The output current of CSOUT is the product of the
voltage measured between SENSE and IN and the transconductance gain (2500 F S typ).
Ground
Gate-Driver Output. Connect GATE to the gate of the external n-channel MOSFET switch.
MOSFET Source Voltage Input. Connect SOURCE to the source of the external n-channel MOSFET.
Active-Low, Open-Drain Fault Output. When an overcurrent occurs, FAULT goes low.
Calibration Mode Select Input
Internally Connected. Connect to ground.
Bias Input. Connect BIAS to REG.
Exposed Pad. Connect to AGND.
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX5980EVKIT#
EVAL KIT MAX5980
MAX5982CEVKIT#
EVAL KIT MAX5982C
MAX6397SATA+T
IC SW OVERVOLT PROT 8-TDFN
MAX6496EVKIT+
KIT EVAL FOR MAX6496
MAX6651EVKIT
EVAL KIT FOR MAX6651
MAX7325EVKIT+
KIT EVAL FOR MAX7325
MAX7326EVKIT+
KIT EVAL FOR MAX7326
MAX7359EVKIT+
KIT EVAL FOR MAX7359
相关代理商/技术参数
MAX5977AEVKIT+
功能描述:热插拔功率分布 1V to 16V Hotswap Controller with Precision Current Sensing Output RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977BETP+
功能描述:热插拔功率分布 1-16V Hot-Swap Controller
RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977BETP+T
功能描述:热插拔功率分布 1-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5977ETP+
制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX5978ETJ+
功能描述:热插拔功率分布 0-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5978ETJ+T
功能描述:热插拔功率分布 0-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5980EVKIT#
功能描述:电源开关 IC - POE / LAN MAX5980 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6
MAX5980EVKIT+
功能描述:电源开关 IC - POE / LAN RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6